2.4Ghz Esky Honey Bee 4-Channel RC Helicopter RTF (include: Helicopter, 2.4G, Charger, RTF)
  | | |
| |
| 【2.4GHz transmitter 】2.4GHz
Remote control system with high stability and non frequency interfering
|
| |
|
TWF Company newly designed 2.4G frequency band,"2.4G" RC system
with advanced Spread Spectrum Technology and digital FSK(frequency shift
key)Coding Technology,whith manifested tremendous vantage compared to
traditional transmitter. |
- Channel:4
- Charger port:yes
- Simulator port：Yes
- Trainer switch:Yes
- Power resource:1.5V*8"AA"Battery
- Modulation type：FM
- RF power:≤14±1.5dBm
- Static current:≤6-8mA
- Voltage display type:LED
- Size:189*205*55mm
- Weigth:560g
- Color:black
- Antenna length:14.5cm
- Use Range:airplane,helicopter
- Certificate:CE,RoHS
|
 | | | | |
| |
【Products features:】 |
|
| |
(1).Traditional remote control distance is about 250
meters,required a transmitter with 750mW transmitting power consumption,but 2.4G
transmitter just need 4mW power consumption.
(2).2.4G Channel with wide
use,can generate corresponding frequency throuth binding or FSK,there will be no
frequency interfering when fly simultaneously.
(3).2.4G remote control
system adopts superintegrated frequency synthesis and FSK(frequency shift
key)technology,which can automatically program and set the working frequency
under the supporting of microprocessor.Flyers would enjoy a free flight without
changing crystal.
(4).With dual transmission characteristic,the data will be
in dual transmission&confirmation between transmitter and receiver.So
probabilize many extended functions.
(5).With the characteristics of quick
response,high precision and nonservo quiver.
(6).2.4Ghz RC System frequency
wave range is 1/4 of the usual used frequency wave range,because 2.4GHz device
with high frequency,short wave range,so the transmitter antenna is just 14.5cm
in length.
|
|
|
 |
(1).Item
Number:EK2-0424
(2).Dimension:50*24*15mm
(3).Color:Dark
green
(4).Antlength:14.5cm
(5).Certificate:CE,RoHS
| |
| |
【Regulation and operating procedure of 2.4G RC
System:】 |
|
| |
Binding for RC System of each model has been completed in
factory,without needing to debug again.
Normal operation manifested as
below:
Power on the transmitter, the indicator of 2.4G transmitter will twinkle for
3 seconds, which indicates that transmitter is sending code binding information.
After 3 seconds, the twinkling 2.4G transmitter indicator becomes solid,?Then
connect the receiver or 4in 1 mix controller, observe the receiver or 4 in 1 mix
controller, 2.4G transmitter indicator twinkles two times and gets solid, which
indicates that the reception of the channel data is successful and are ready to
fly.
Turn on the transmitter and power on the helicopter. LED indicator of
receiver or 4 in 1 mix controller go out after twinkling two times, indicating
that binding is failing and need to unbind firstly and rebind.
1.How to
unbind?
Turn off the transmitter，Connecting the battery to receiver, Press
the bind keystoke for 1 or 2 seconds LED indicator of Receiver will twinkle
constantly,  which indicates that unbinding has completed.(As shown in
the right picture)
2.Rebind
Firstly disconnect the receiver and 4 in 1 mix
controller, then connect the receiver or 4 in 1 mix controller to the power，the
state indicator twinkles slowly, which indicates that receiver is receiving
signal. Then Power on the transmitter，if the indicator of RX display from slow
twinkling to rapid twinkling, then solid, which indicate the binding is
successful.(Note: transmitter just will transmit code in first 3 seconds, if
receiver can not receive code within 3 seconds, please turn on the transmitter
again.)
|
| 【Remarks:】 |
1.Power on the transmitter, indicator twinkles 50times within 3 seconds of
binding period, the indicator get solid after the binding.(Please note that in
the process of binding, first connect the receiver or 4 in 1 Mix controller
before powering on the transmitter)
2.If binding is not successful, the
indicator of receiver or 4 in 1 mix controller will twinkle two times then go
out.
3.Since different manufacturers have different frequency band, channel
and different coding and decoding method, so different products are
incompatible, all RC system should be under the original trademark.
4.Do turn
on the transmitter once again in each
binding. | |
|
